We know that the gearbox is one of the important devices on the car, so it is very important to maintain and select the gearbox. Many automobile maintenance companies in Jinan have set up some Jinan automatic transmission maintenance, Jinan gearbox maintenance professional repair shop. Since the gearbox is so important to the car, today we would like to work with you about the disassembly and assembly precautions of automatic transmission maintenance.

在此小編要提醒大家提醒大家，對于變速箱的維修一定要找具有維修經驗的公司維修!對于自動變速箱維修時的拆裝注意事項，主要有以下五點：

In this section, I would like to remind you that for the maintenance of the gearbox, you must find a company with professional maintenance experience to repair! For the disassembly and assembly precautions of automatic transmission maintenance, there are mainly the following five points:

1、先卸下萬向節螺釘，使變速器和傳動軸的萬向節分離;再卸下離合器罩螺釘，使變速器和離合器分離;如果是遠程操縱的變速器，則將操縱機構與變速器本體分離將變速器從汽車上拆卸下來。

1. First remove the universal joint screw to separate the universal joint of the transmission and transmission shaft; then remove the clutch cover screw to separate the transmission and clutch; if it is a remote control transmission, separate the control mechanism from the transmission body, and finally remove the transmission from the vehicle.

2、清洗變速器外部的油泥和污物，注意保護前后的軸頭。

2. Clean the oil sludge and dirt outside the transmission, and pay attention to protect the front and rear axle heads.

3、擰下放油螺塞，放凈變速器中的潤滑油，再琶油螺塞。

3. Screw the drain plug, drain the lubricating oil in the transmission, and then plug the oil plug.

4、找一個干凈無灰塵的場地，利用拆卸工具和銅棒，開始拆卸變速器。拆卸順序一般是：變速器蓋、軸、第二軸、中間軸、倒擋軸。5、拆卸零件時，先看好零件原始的方向和位置后再拆卸，必要時，做好記錄;拆下的零件按拆卸先后順序，分部位排放整齊，必要時可用線或鐵絲將各零件按順序串在一起;齒輪可按原方向和位置套在軸上，以防裝錯或漏裝。

4. Find a clean and dust-free place and use the removal tool and copper bar to start disassembling the transmission. Generally, the disassembly sequence is: transmission cover, first shaft, second shaft, intermediate shaft and reverse gear shaft. 5. When disassembling parts, take good care of the original direction and position of the parts before disassembly. If necessary, make records. The removed parts shall be arranged in order according to the disassembly sequence. If necessary, wire or iron wire can be used to string the parts together in order; the gear can be set on the shaft according to the original direction and position to prevent wrong or missing assembly.

以上就是今天小編要和大家分享的相關知識，希望對大家有所幫助。

The above is today's small editor to share with you the relevant knowledge, I hope to help you.