We know that gearbox is one of the important devices in automobile, so it is very important for gearbox maintenance and selection. Many automobile maintenance companies in Jinan have set up a number of Jinan automatic gearbox maintenance, Jinan gearbox maintenance professional repair shop. Since the gearbox is so important to the car, today we have to work with you about the precautions for disassembling the automatic gearbox during maintenance.

在此小編要提醒大家提醒大家，對于變速箱的維修一定要找具有維修經驗的公司維修!對于自動變速箱維修時的拆裝注意事項，主要有以下五點：

In this small edition, we should remind you that you must find a company with professional maintenance experience for the maintenance of the gearbox. For the disassembly and assembly precautions during the maintenance of the automatic gearbox, there are the following five points:

1、先卸下萬向節螺釘，使變速器和傳動軸的萬向節分離;再卸下離合器罩螺釘，使變速器和離合器分離;如果是遠程操縱的變速器，則將操縱機構與變速器本體分離將變速器從汽車上拆卸下來。

1. First remove the universal joint screw to separate the transmission and the universal joint of the transmission shaft; then remove the clutch cover screw to separate the transmission and the clutch; if the transmission is remotely operated, separate the control mechanism from the transmission body and finally remove the transmission from the vehicle.

2、清洗變速器外部的油泥和污物，注意保護前后的軸頭。

2. Clean the mud and dirt on the outside of the transmission, and protect the front and rear axle heads.

3、擰下放油螺塞，放凈變速器中的潤滑油，再琶油螺塞。

3. Screw down the oil drain plug, drain the lubricating oil in the transmission, and then plug the oil.

4、找一個干凈無灰塵的場地，利用拆卸工具和銅棒，開始拆卸變速器。拆卸順序一般是：變速器蓋、軸、第二軸、中間軸、倒擋軸。

4. Find a clean and dust-free place, use the removal tools and copper bar, and start to remove the transmission. The removal sequence is generally: transmission cover, first shaft, second shaft, intermediate shaft and reverse gear shaft.

5、拆卸零件時，先看好零件原始的方向和位置后再拆卸，必要時，做好記錄;拆下的零件按拆卸先后順序，分部位排放整齊，必要時可用線或鐵絲將各零件按順序串在一起;齒輪可按原方向和位置套在軸上，以防裝錯或漏裝。

5. When disassembling parts, first look at the original direction and position of the parts, and then disassemble them. If necessary, make records. The disassembled parts shall be arranged orderly according to the disassembly sequence, and the parts can be strung together by wire or iron wire if necessary. The gear can be sleeved on the shaft according to the original direction and position to prevent wrong or missing installation.

以上就是今天小編要和大家分享的相關知識，希望對大家有所幫助。如果大家還有相關疑問，歡迎來到官網咨詢客服

The above is the relevant knowledge that Xiaobian wants to share with you today, hoping to help you. If you have any questions, welcome to the official website for customer service